scd#qm 5299 source control drawing upscreening/manufacturing specification p/n ft20c16 - 45emb - x title page ................................ ................................ ................ list of effective pages ................................ .............................. change list ................................ ................................ .............. definitions ................................ ................................ ................. acronyms and abbreviations ................................ ..................... contents. 1 introduction /purpose ................................ ................................ . 2 reference documents ................................ ............................... 3 source of parts ................................ ................................ ......... 3.1 original part manufacturer ................................ ......................... 3.2 screening company ................................ ................................ ... 3.3 uk supplier ................................ ................................ ............... 4 manufacturing ................................ ................................ ........... 4.1 screening ................................ ................................ ................. 5 certificate of conformity ................................ ............................ 5.1 ft certificate of conformity ................................ ....................... 6 package description ................................ ................................ .. 6.1 mar king ................................ ................................ .................... 7 traceability ................................ ................................ ............... 8 component selection ................................ ................................ . 8.1 general ................................ ................................ .................... 8.2 nuclear hardness ................................ ................................ ...... 8.3 baseline component ................................ ................................ . 8.4 obsolescence notice ................................ ................................ . date - 200603 iss - 1 rev - changes - orig name - mlsalmon date - iss - rev - changes - name - date - iss - rev - changes - name - date - iss - rev - changes - name - date - iss - rev - changes - name - date - iss - rev - changes - name - force technologies ltd 2003 tm
1 introduction/purpose this document specifies the manufacturing, procurement details and screening requirements. in b rief the part is: high speed novram a package description is given in section 6 of this document. 2 reference documents test method and procedures for microcircuits general specs for hybrids sort, incoming and outgoing inspection procedures mil - std - 883 (latest issue) mil - prf - 38534 department of defence washington dc 20363 - 5100, usa 3 source of parts this section provides an overview of the companies involved in the manufacture, screening and supply of the part. original procurement of parts shall be from the address specified in section 3.3. 3.1 original part manufacturer the original part: die are/were produced by : xicor manufacturer:xicor address: 1511 buckeye drive milpitas ca95035 - 9985 the donor part number is: x20c16w 3.2 assy /manu ,/ screening company the above parts are then assembled and screened by: classified disclosure under nda or disclosed as: 3.3 uk supplier the assembled/screened parts shall be procured from: force technologies ltd ashley court, henley, marlborough, wilts, uk sn8 3rh tel: +44(0)1264 731200 fax: +44(0)1264 731444 the force technologies part number(ordering code) is: ft20c16 - 45emb - x qm 5299 4.0 manufacture (manufacturing processes, assembly, screen and test equipment listings available for inspection upon request. part number breakdown ft20c16em b - 45 - x e = 32lcc mb = mil - std - 883 x = xicor 45 = 45ns =
4.1 screening the ft20c16 - 45emb - x shall be screened as specified in the table below. all batches of parts shall be supplied with a certificate of conformity. the certificate of conformity shall reference the screening specified below. screening method req.t note visual inspection incoming and outgoing inspection procedures 100% 1 internal visual (pre - cap) 2010 cond b (applicable to packaging parts) 100% destructive tests optional temperature cycling 1010, test condition c 100% constant acceleration 2001, test condition e (min) y1 orientation only 100% seal a. fine b. gross 1014 a1 c 1 100% visual inspection 100% interim electrical sub group 1&7 100% burn - in test 1015, 160 hours at 125 c minimum 100% percentage defective allowable (pda) 5 percent qci group a all lots 2 final electrical test group a all subgroups 100% 3 final electrical test a) static tests 5005 1)subgroups 1(25oc) 2(+125oc0) 3( - 55oc) b) dynamic test or switching test 1) subgroup 4 or 9 (25oc) c)functional test 1) subgro up 7(25oc) 8a(+125oc) 8b( - 55oc) default procedure parameters in accordance with applicable device specification. 100% 3 external visual 2009 100% radiation latch - up 1020 optional group b 5005 optional group c 5005 optional group d 5005 optional notes: 1/ for pre - assembled product 2/ manufactured batches shall have lots tests carried out i n accordance with mil - std - 883 3/ part no. x20c16emb45 data sheet included on .pdf copy manufacturin g die visual 2010 cond b 100% die attach jm7000 & cure 2019.5 100% die shear 2019.5 visual inspection 2010.1 wire bond .00125 alum wire bo nd strength 2023.5 visual 2010.1 preseal visual 2010.1 mil std 883 100% preseal vacuum 1 hour min 150oc under vacuum seal solder seal in belt furnace under nitrogen
mil screening as above marking cure 125oc 60 mins final inspection 2009.9 5 certificate of conformity all batches of parts shall be supplied with certificates of conformity. the certificate of conformity shall reference the test certificate. 5.1 ft cof c screening specified in section 4 of this document. force technologies part number. 6 package description package:32 pad lcc type e pin - out:as x20c16e finish: hot tined dip mil - prf - 38534 appendix e. 6.1 marking part number (will exclude die manufacturer if space limited) qm no date code batch code ft logo 7 traceability ( if applicable) traceability shall be provided by the date code printed on the top/bottom side of each device. iso9002 traceability procedures to apply using batch codes 8 component selection 8.1 general no component or component supplier shall be chang ed without the express written consent of the customer(s), following the submission of evidence to justify that the replacement component will meet all required parameters, including radiation immunity. 8.2 nuclear hardness (not applicable) 8.3 the bas eline component: original manufacturer: manu:xicor part number: p/n:x20c16w the vendor shall determine that the die size, mask and if possible the manufacturing process has not changed since the manufacture of the baseline component. this shall be done prior to acceptance of any order by the vendor. if such a change has occurred, written notification shall be given to the customer the changes and possible alternatives. the vendor shall take no further action until a way forward has been agreed with the customer. 8.4 obsolescence upon acceptance of an order the vendor becomes responsible for all component obsolescence until completion of that order. the vendor will inform customer of any pcn. ashley crt, henley, marlborough, wilts, sn8 3rh tel: +44(0)1264 731200 fax:+44(0)1264 731444 e - mail info@forcetechnologies.co.uk tech@forcetechnologies.co.uk sales@forcetechnologies.co.uk www.forcetechnologies.co.uk
all trademarks acknowledged unless otherwise stated in this scd, force technologies ltd reserve the right to make changes, without notice, in the produ cts, including circuits, cells and/or software, described or contained herein in order to improve design and/or performance. force technologies resumes no responsibility or liability for the use of any of these products, conveys no licence or any title und er patent, copyright, or mask work to these products, and makes no representation or warranties that that these products are free from patent, copyright or mask work infringement, unless life support applications force technologies products are not designed for use in life support appliances, devices or systems where malfunction of a force technologies product can reasonably be expected to result in a personal injury. force technologies customers using or selling force technologies products for use in such applications do so at their own risk and agree to fully indemnify force technologies for any damages resulting from such improper use or sale. copyright force technologies ltd 2003
|
